Experimental drying times you can expect for your equipment for different wetsuit thicknesses and weather conditions.
||Ambient Temp. 85ºF / 29ºC
||Ambient Temp. 65ºF / 18ºC
||Ambient Temp. 45ºF / 8ºC
||Requires inside out
|4 to 5mm
|+6mm / other equipment
Dimensions and operating measures
- Dimensions: 428mm x 170mm x 199mm (Due to its size, it may not be suitable for small children’s wetsuits).
- Weight: 1450 grams / 3.2 lb
- Fan design airflow: 290 m3/h or 5000 litres/min
- Fan impeller maximum rotating speed: 2,800rpm
- Airflow direction: 360º
- Optimized safe heating element power: 220v – 590W / 110V – 450W
- UL certified Dual Thermostat : redundant temperature controlled switches at 90 ºF / 32ºC
- Home connection adapter: 110v and 220v available with USA, EU, UK, CH and AU wall plugs.
- Car connection adapter (sold separately): 12v to 220V at 150W, rated to power Blawesome in Fan-only mode.
Extend your equipment lifespan beyond known horizons
A wetsuit exposed to direct sunlight to dry will reduce its lifespan to less than a half. On the other hand, a wetsuit in a humid area on winter may take days to completely dry.
Get perfect drying results and protect your favorite equipment for many years using the right device.
MADE TO LAST
+10000h expected lifespan
THERE ARE MANY ASPECTS TO SURFBOARD SELECTION THESE ARE THE POINTS TO CONSIDER
Typically surfboards are measured in inches. The length is measured from the nose to the tail. Choosing the length of the surfboard is dependant on your size (weight, height), board type and waves conditions you wish to use the board for.
The widest point of the surfboard is measured from rail to rail. Generally the wider the surfboard the more stable the board, while a board with smaller width maintains better speed and performance.
Surfboard thickness is measured from the top deck to the bottom. The thickness again has a bearing on the board’s performance. Professional surfers will tend to go for the thinner boards as they are lighter and offer better performance.The thicker boards are stronger and because there is more foam under the surfer the boards are more stable.
The bottom curve of a surfboard. Generally the more rocker the surfboard has the more loose (manoeuvrable) the surfboard will be. Where the flatter rocker surfboards will be faster, although they will lack the looseness. The nose is the tip of the surfboard, the nose can vary in shapes and size. Basically the thinner the nose the more response the board will perform, while wider noses are better for stabilization.
Used to increase the strength of a surfboard, a stringer (normally made from wood) runs down the length of a surfboards (typically in the centre of the board from the tip of the nose to the tail).
Boards built with Epoxy, Carbon Fibre and soft boards generally don’t have stringers.
Generally heavier surfers require larger fins to hold the waves better. Although if you prefer to ride a looser (less hold in the waves), smaller fins would be a better option.
Fin configurations have an effect on the ways your surfboards perform.
The following are some of the more common fin configurations.
The single fin was the original fin configuration for surfboards. Based on the idea of the sailboat keel. Single fins are added stabilization and control on the powerful, larger waves, although lack manoeuvrability
Are great for small waves, being fast and manoeuvrable, but when put into tight spots on larger waves, they become hard to control. Popular with Fish surfboards.
THRUSTER 3 FIN
Widely recognized as the standard fin configuration, the thruster answers the shortcomings of the single fin and the twin fins configurations.
The thrusters give you stabilization, control and manoeuvrability in all types of surfing conditions.
This concept was the brainchild of Australia’s Simon Anderson
QUADS 4 FINS
With four fins in the water, Quads boasts an extraordinary amount of holding power in larger surf.
You may think that having four fins would sacrifice speed by creating more drag, but this is not the case.
The both sets of fins are working together on the rail, which makers believe they creates less drag than a board with a centre fin.
The manoeuvrability isn’t sacrificed either, with fins directly under your back foot, the quads are very responsive.
Similar setup to the Twin Fin, although smaller (low profile) fins are generally placed wider (closer to the rails) on the surfboard.
Popular with Fish and Egg / Retro surfboards.
Heeft u hulp nodig bij uw aankoop? Neem dan gerust contact met ons op
+3170 201 5153